Search
Close this search box.

Galaxy DX2547 Base Cb Radio

$ 399.99

Galaxy DX2547 Base CB Radio with Sideband

SELECT YOUR OPTIONS

Performance Upgrades *

Note: Some 10 meter radios come with echo from the factory. No cb radios come with echo from the factory. Check options (or picture) before adding echo.

SSB Optimization – Frequency Alignment

Alignment of the TX/RX frequencies are critical for SSB operation. We recommend an open clarifier mod be performed on radios such as Galaxy 949, 959, 979, 99, 94, 98, 2547, 2517.

Description

DESCRIPTION

Button: Power – Turn radio on and off
Knob: Talkback – Turn your monitor on/off and adjust the loudness of your voice playback
Knob: RF Power – Adjust the level of your output power
Knob: SWR-Mod-PWR – Three position switch controls what the meter is measuring – Meter measurers antenna SWR’s, Modulation and RF Power during transmit. Meter reads RF Power receive level when not transmitting
Dual Knob: Mic / RF Gain – Adjust your modulation (voice) level – Control your RF gain (receive signal)
Dual Knob: Dim/Tone – Adjust the brightness of your lights – Adjust the tone coming from your speaker
Button: RB – Roger Beep
Button: PA – Public Address (loud speaker required)
Center Dial: Channel changer
Button: ANL – Automatic Noise Limiter on/off
Button: NB – Noise Blanker
Button: GNF – Galaxy Noise Filter
Button: Clarifier – Allows the Clarifier knob to fine tune frequencies.
Knob: USB / AM / LSB – Select the mode of operation between standard AM and Single Side Band operation (upper side ban / lower sideband)
Knob: 9 / Normal / 19 – Bypass the channel selector knob by quickly toggling between channel 9 and 19
Knob: Squelch – Tune out unwanted white noise by turning up your squelch. Only the strongest signals will come through
Knob: Volume – Volume control

Included Radio – Microphone – Mounting bracket and hardware – AC and DC Power cord – Mic hanger – Owners manual

EXPLANATION OF OPTIONAL UPGRADES

  • Performance Tuning – From the factory, radios perform below standard. Your radio will be optimized for best transmission performance – Modulation will be set to achieve 100% – The power will be professionally aligned to the highest output allowed by law
  • Receive Enhancement – Your radio will be optimized for the best receiving performance – Schottky barrier diodes will replace cheaper diodes in the receive circuitry, the first stage receive transistor will be replaced with a more sensitive better performing transistor and the radio will be professionally aligned.
  • Echo Sound Board-This sound board allows the operator to adjust the amount of reverb controlling both the volume and delay giving you that big radio sound, better overall modulation and more clear transmission. You can also use it to annoy others by messing with the adjustments. This dual control knob, by default, will take the place of the delta-tune knob on many radios like some Cobra 29 radios. Other times, the echo control knob will be installed on the side, as is often the case with some Galaxy radios like the dx939, 959 and dx979, unless other custom arrangements have been made with us. On the DX2547 Base, the Echo Control will be installed in place of the head phones jack just above the microphone jack. An extension speaker/small head phone jack is still available on the rear of the unit.
  • Nitro Light Rings – Colorful LED rings will be installed behind the control knobs. They can be installed behind the original knobs giving it a back-glow effect or you can choose to have Clear Knobs installed in place of the factory originals. These knobs will glow the color of the LED rings you choose. Typically, a dimmer control is installed to adjust the brightness. This knob often replaces the delta-tune knobs on most Cobra radios as that control knob is not necessary. In cases where an Echo control knob is installed in place of the delta-tune knob, the dimmer is normally installed in place of the rf gain (receive strength). The rf gain control will be bypassed, thus setting the strength to high.
  • Clear Knobs – As explained in the Nitro Light Rings section, the radios factory original knobs can be replaced with Clear Knobs. This can be done with or without installing the Nitro Light Rings. When installed in front of the Nitro Light Rings, the Clear Knobs will glow brightly. Without the Nitros, the clear knobs simply give your radio a nice clean modern look.
  • Channel and Meter Lights – You can choose to change the color of the channel LED and the meter light. You can also choose to change the color of the frequency display on radios that have one. As an example, the Cobra 29 LTD Classic has a green channel LED and clear meter light. If you decide to install blue Nitro Light Rings, you may also want to change the channel LED and meter light to blue. A Galaxy DX939 has blue channel LED’s, a blue meter light and a blue frequency display. If you install red nitro lights, you may also want to change the channel, meter and frequency display to red as well. Build it like you want it.
  • SSB Optimization/Alignment – If you plan on using SSB on a Galaxy radio, (959, 979, 2547, 99, 94, 98) it is highly recommend that the frequency clarifier be opened and the radio realigned. An open clarifier means your transmit and receive will track on the same frequency. When you tune in another radio operator, you will automatically be tuning your transmit onto the same frequency they’re transmitting.

This product complies with fcc regulations for Citizen Band radios, not to exceed 4 watts carrier AM, 12 watts SSB, 100% modulation. Stock radios perform well below legal limits and are not always aligned for optimum receive and transmit, therefore; we recommend taking advantage of the performance options. Feel free to contact us for any questions concerning performance enhancements.

Additional information

Weight 18.8 lbs
Dimensions 18 × 9 × 14 in